Model 909 Payphone Users Manual FEATURES: * Coin operated line powered payphone. * Automatic answer without push to talk button. * Keypad programmable. * Multi coin phone: accepts nickels, dimes, quarters, and dollar coins. * Touch-tone dialing. * Volume control button * Ringer On/Off switchable. * Phone emits warning tone 15 seconds prior to end of call. * Phone display BUSY on LCD screen when call is busy. * Phone display SIT TONE when you dial a vacant or invalid number. FACTORY PRESETS: * Tone dialing * Local calls: $0.25 for 3 minutes. * Long distance calls: $0.75 for 1 minute. * Information calls (1411/411): $0.50 for unlimited time. * Restricted calls: operator, international, 1900, 1976, 976, and 1700. * Free calls: 1800, 1888, 1877, and 911. * Incoming calls for unlimited time. * Allow 0+, calling cards, and credit cards calls. * Pass Code: 000000 IMPORTANT: It is recommend that you read the 909 users manual prior to installation and programming the phone. TO INSTALL THE 909 PAYPHONE: Simply plug the phones line cord into a standard RJ11 outlet provided by the phone company. TO REMOVE THE COIN BOX: Locate the metal tabs at the rear of the phone and pull the top tab back. This will allow the coin box to be removed. To lock the coin box close the tab and insert a pad lock (not provided with phone) between the two holes of the tabs. TO USE THE PAY PHOHE: 1. Lift handset, LCD display will show HELLO. 2. Dial desired phone number, the display will show the amount to be deposited. 3. Deposit the amount requested. 4. The phone will connect the call, if the call is answer the money will be collected automatically and you will be able to talk to the other party. 5. If you get a busy tone or a no answer signal, hang up the handset and the money will be refund. PROGRAMMING REFERENCE: Note: All programming must be done in the program mode. The first important thing you need to do is to change factory preset pass code. For all programming press # to save the entry, press * to cancel. To enter the program mode: 1. Enter # then the six digit pass code 000000, the display will show FLASH then FREE 2. Enter preset pass code, *#000000, the display will show P-, you are now in the program mode To change factory pass code: 1. Enter *96 the display will show the old pass code 2. Enter your new 6-digit pass code 3. Enter # to confirm, display will show PASS If you forget your pass code: 1. With the phone hang up, remove the tap underneath the base to reveal the dipswitches 2. Dipswitches should be dipswitch-1 off, dipswitch-2 on, and dipswitch-3 on. 3. Put dipswitch-1 on and go off hook 4. Enter #000000 display will show FLASH then FREE 5. Enter *#000000 display will show P- 6. Put dipswitch-1 off 7. Enter *96 and your new 6-digit pass code, enter # to confirm and display will show PASS. 8. The pass code becomes your own 6-digit number. To use Dipswitches: ` Dipswitch-1 resets pass code. It is used as above. ` Dipswitch-2 sets tone or pulse dialing. For tone dialing, put it on, for pulse dialing, put it off. ` Dipswitch-3 sets ringer on or off. To check the amount of money in the coin box: 1. Enter *97 the display will show the cash amount 2. Enter # to reset or enter * to exit Example: 00075 is $0.75, 00100 is $1, and 20000 is $200 To erase old program settings: 1. Enter *99, display will show [99] CLr 2. Enter # to confirm, display will blink CLr ----, then show PASS To reset factory preset: 1. Enter *98, display will show [98] COPY 2. Enter # to confirm, display will blink COPY ----, then show PASS To set phone for PBX: To set phone to work on a PBX but you will manually dial the prefix i.e. or 9. 1. Enter *13 2. Enter 1 then your 1-digit extension 3. Enter # to confirm, display will show PASS To set phone to work on a PBX but to automatically dial the prefix i.e. 0 or 9. 1. Enter *13 2. Enter 2 then your 1-digit extension 3. Enter # to confirm, display will show PASS To set phone for regular line: (preset by factory) 1. Enter *13 2. Enter 00 3. Enter # to confirm, display will show PASS Incoming calls: (preset as unlimited time) 1. Enter *14 2. Enter your 2-digit time limit; it can be set for 01 minute to 98 minutes 3. Entering 00 will restrict incoming calls; entering 99 will allow unlimited time on incoming calls 4. Enter # to confirm, or enter * to cancel Example: To set incoming time limit to 5 minutes. 1. Enter *14 2. Enter 05 3. Enter # to confirm, display will show PASS Free calls: (do not used any used by factory, refer to factory preset) There are 20 different locations you can used to allow 20 different free calls up to 12 digits. These locations are *40 thru *59. To allow a particular number to be free enter any locations from *40 thru *59. Enter that particular number, if the number is less than 12 digits enter # after the last number. Then enter # to confirm or enter * to cancel. Example: To allow the number 281-550-5592 to be free. 1. Enter *45 2. Enter 2815505592# 3. Enter # to confirm, display will show PASS, or enter * to cancel the entry. Restrict calls: (do not used any used by factory, refer to factory preset) There are 20 different locations you can used to restrict 20 different numbers up to 12 digits. These locations are *20 thru *39. To restrict a particular number enter any locations from *20 thru *39. Enter that particular number, if the number is less than 12 digits enter # after the last number. Now enter # to confirm or enter * to cancel. Example: To restrict 011 calls. 1. Enter *28 2. Enter 011# 3. Enter # to confirm, display will show PASS, or enter * to cancel the entry. Rate bands: *00 thru *12 allows you to create a total of 13 types of rate bands. The rate is set by an initial charge and time limit (in seconds) followed by an additional charge and time limit (in seconds). RATE-BAND RATE-NUMBER INITIAL-RATE & TIME-LIMIT ADDITIONAL-RATE & TIME-LIMIT *00 00 025180 025180 *01 01 075060 075060 *02 02 050999 000999 *03 03 Empty Empty *04 04 Empty Empty *05 05 Empty Empty *06 06 Empty Empty *07 07 Empty Empty *08 08 Empty Empty *09 09 Empty Empty *10 10 Empty Empty *11 11 Empty Empty *12 12 Empty Empty ` *00 is used by factory preset for local calls set at $.25 for the first 3 minutes and $.25 for each additional 3 minutes. ` *01 is used by factory preset for long distance calls set at $.75 for the first minute and $.75 for each additional minute. ` *02 is used by factory preset for information calls (1411 & 411) set at $.50 for unlimited time. ` To create a rate band enter any empty rate band from *00 thru *12 and set up the initial rate and time limit followed by the additional rate and time limit. Example: To set up a rate band to charge for $.50 the first 3mins. and $.25 each additional 2mins. 1. Enter *03 2. Enter 050180 025120, the initial rate 050180 is 50 cents for 180 seconds, the additional rate 025180 is 25 cents for 120 seconds. 3. Enter # to confirm, display will show PASS, or enter * to cancel the entry. Assign area codes or prefixes to rate bands: (do not use any used by factory, refer to factory preset) There are a total of 100 3-digit memory locations that may be used to assign special area codes and/or prefixes to a particular rate band (*00 thru *12). These 3-digit memory locations are 000 thru 099. You may first create a rate band containing charges and time limits you want (see rate bands), and then assign an area code or area code/prefix in a particular 3-digit memory location from 000 thru 099.. Enter # after the last number if the area code and/or prefix is less than 7 digits. Now enter your rate number for the particular rate band you created and enter # to confirm. Example 1: To assign the area code 1-281 to the long distance rate band in the memory location 056. (assume *01 is kept as factory preset.) 1. Enter 056 1281#01 2. Enter # to confirm, display will show PASS, or enter * to cancel the entry. Example 2: To assign the area code 1-713 and prefix 551 to charge for $.75 for the first minute and $.25 for each additional minute. First create a rate band (we choose rate band *10) 1. Enter *10 2. Enter 075060 025060 3. Enter # to confirm, display will show PASS Then assign the area code and prefix to a particular 3-digit memory location and assign it to the rate band we just create by the rate number. (we choose 3-digit memory location 088) 1. Enter 088 171355110 2. Enter # to confirm, display will show PASS To allow/disallow 0-calls: (factory set to disallow) To allow 0-calls: 1. Enter *60 2. Enter 1 3. Enter # to confirm, display will show PASS To disallow 0-calls: 1. Enter *60 2. Enter 0 3. Enter # to confirm, display will show PASS To enable/disable 0+ rerouting calls: (factory set to enable) To enable 0+ rerouting calls: 1. Enter *61 2. Enter 1 3. Enter # to confirm, display will show PASS To disable 0+rerouting calls: 1. Enter *61 2. Enter 0 3. Enter # to confirm, display will show PASS Cut off time: (factory set as 5 second) *62 is programmed to set a cut off time on calls using 0 or Operator for the leading number prior to the prefix. If additional numbers are not entered within the preset time, the connection will be broken and deposited coins will be returned. This function is effective only under the condition that there is not a reroute number in *63. To change the cut off time: 1. Enter *62 2. Enter the 1-digit time limit in seconds 3. Enter # to confirm, display will show PASS Example: To set the cut off time to 3 seconds. 1. Enter *62 2. Enter 3 3. Enter # to confirm, display will show PASS To reroute number: *63 is used to program a 0+reoute number that will be dialed out when you dial 0. This number can be up to 29 digits, if the number is less than 29 digits enter # after the last number. The factory preset reroute number is 1-888-456-2277 pause 2815505592. Example: If you want to set up the reroute number as 1010222 . [ed; 1010222 PIC CODE = MCI Telecommunications] 1. Enter *63 2. Enter 1010222*0#, the display will show [63] 1010222-0= 3. Enter # to confirm, display will show PASS When customers dial 0-281-550-5592, the phone will actually dial 1010222 pause 0-281-550-5592. * Is to put a pause in the reroute number. Example: If you want to set up the reroute number as 1-888-456-2277 pause 2815505592. 1. Enter *63 2. Enter 18884562277*28155055920#, display will show [63] 18884562277-28155055920= 3. Enter # to confirm, display will show PASS When customers dial 0-956-855-2345, the phone will actually dial: 1-888-456-2277 pause 281-550-5592-0-956-855-2345. To set the pause time in the reroute number: (factory set at 5 seconds) 1. Enter *64 2. Enter the time in seconds (1-digit) 3. Enter # to confirm, display will show PASS Example: To set the pause time to be 3 seconds. 1. Enter *64 2. Enter 3 3. Enter # to confirm, display will show PASS To clear the reroute number: 1. Enter *63 2. Enter # 3. Enter # to confirm, display will show PASS OWNERS TO MAKE A FREE COINLESS CALL: 1. Enter # then your pass code, the display will show FLASH then FREE 2. You are now able to make a free call ERROR CODE LIST: Error 2: Dial restricted number or invalid numbers. Error 4: Coin mechanism is full or has coin jam. Error 6: You dont dial number for 25 seconds after handset is lifted. Error 7: You dont deposit enough coins for 25 seconds. Error 8: The line is connected for a long time but no one answers. FACTORY PRESETS: *#000000 - Pass code *00 025180025180# - Rate 00 local calls at $.25 for 3mins. and $.25 for each add. 3mins. *01 075060075060# - Rate 01 long distance calls at $.75 for 1min. and $.75 for each add. min. *02 050999000999# - Rate 02 for information (411/1411) set at $.50 for unlimited time limit. *13 00# - Regular line dialing *14 99# - Incoming calls set at unlimited time Restricted calls: *20 1900## - Used to restrict 1900#s *21 1976## - Used to restrict 1976#s *22 976## - Used to restrict 976#s *23 1700## - Used to restrict 1700#s Free calls: *40 1800## - Used to allow 1800 toll free calls *41 1877## - Used to allow 1877 toll free calls *42 1888## - Used to allow 1888 toll free calls *43 911## - Used to allow free emergency 911 calls *60 0 - Used to disallow 0- calls *61 1 - Used to allow 0+ calls *62 5 - Cut off time set at 5 seconds *63 18884562277*28155055920## 0+ Reroute number: 18884562277 and 2815505592 *64 5 - Pause time set at 5 seconds 000 through 099 3-Digit Memory locations: 000 1#01# - 1+ Long distance calls set a rate 01 001 2#00# - 001 thru 008 are 3-digit memory locations used to set local calls at rate 00 002 3#00# - "" 003 4#00# - "" 004 5#00# - "" 005 6#00# - "" 006 7#00# - "" 007 8#00# - "" 008 9#00# - "" 009 1411#02# - 1411 calls set at rate 02 010 411#02# - 411 calls set at rate 02 TECHNICAL SPECIFICATIONS: Complies with part 68, FCC rules FCC Regulation Number: 4NTHA-34299-CX-T Ringer Equivalence: 1.2A U.S.O.C.: RJ11C Model Number: 909 -- Reference: http://www.payphone.com/909manual.htm w w w . n e t t w e r k e d . n e t 0 9 . 2 7 . 2 0 0 0